[RULE] Updating RULE RedHat 9 to most recent bug fixes

[C David Rigby]

I have performed slinky-based installs of RedHat 9 on three systems and 
then updated them to the latest errata-correction RPMs from RedHat.  I 
have collected locally the packages that pertain to a base install of 
RedHat 9 using slinky-v0.3.96.  PLEASE let me know if you discover I 
have missed something!  They can be retrieved here (details in the 
accompanying readme.txt file):

http://rule-test.homelinux.org/~rule/rule-tool/updates/


I do things in a particular order mostly from habit, it may not be 
necessary to follow it strictly.  But at least I know this works, so I 
haven't changed it.  Here are the details:

i686
----

The test server is a dual-PII system.  Prior experience has taught me 
that there is a definite reason why a separate version of glibc exists 
for the i686 CPUs.  On previous RedHat 9 systems, if I installed the 
i386 version, rpm itself began segfaulting, and things degenerated from 
there.

Once the system is running, go to the directory where the i686 packages 
are stored (subdirectory i686 under the server directory shown above) 
and issue the command:

rpm -Fvh kernel-2.4.20-30.9.i686.rpm

(actually, on my system, I issued rpm -Uvh 
kernel-smp-2.4.20-30.9.i686.rpm, but this is not applicable specifically 
to a RULE installation).

Then, from the i386 directory, I update glibc-common with

rpm -Fvh --nodeps glibc-common-2.3.2-27.9.7.i386.rpm

(--nodeps is necessary because the prior version of glibc depends on the 
prior version of glibc-common.  You may be able to issue a single rpm 
command with both the i386 glibc-common rpm and the i686 glibc rpm on 
the command line and let rpm work out the details.  But I haven't tried 
that.)

Back to the i686 directory and

rpm -Fvh glibc-2.3.2-27.9.7.i686.rpm

and while you are at it:

rpm -Fvh openssl-0.9.7a-20.2.i686.rpm

Next, check the file /etc/lilo.conf to make sure you are happy with it, 
run lilo, then reboot.  When the system is running again, go to the i386 
directory and issue the command:

rpm -Fvh *rpm.

Finally, go to the noarch directory and run

rpm -Fvh redhat-config-date-1.5.15-1.noarch.rpm

Done (Well, until the next erratum is released!)

i586
----

Similar to the above, go to the i586 directory and upgrade the kernel:

rpm -Fvh kernel-2.4.20-30.9.i586.rpm

Then, go to the i386 directory and take care of glibc:

rpm -Fvh --nodeps glibc-common-2.3.2-27.9.7.i386.rpm
rpm -Fvh glibc-2.3.2-27.9.7.i386.rpm

Check /etc/lilo.conf, run lilo and reboot.  Finish by going to the i386 
directory and issuing:

rpm -Fvh *rpm

Finally, go to the noarch directory and run

rpm -Fvh redhat-config-date-1.5.15-1.noarch.rpm

Done.

i386/i486
---------

The RULE installation will have installed the 
kernel-2.4.20-8RULE.i386.rpm or the kernel-BOOT-2.4.20-8.i386.rpm kernel 
package.  The updates include kernel-2.4.20-30.9.i386.rpm, which I am 
using without problems (so far) on my 486 notebook.  So, from the i386 
directory:

rpm -Uvh kernel-2.4.20-30.9.i386.rpm
rpm -Fvh --nodeps glibc-common-2.3.2-27.9.7.i386.rpm
rpm -Fvh glibc-2.3.2-27.9.7.i386.rpm

Check /etc/lilo.conf, run lilo, reboot.  Then returning to the i386 
directory:

rpm -Fvh *rpm

Finally, go to the noarch directory and run

rpm -Fvh redhat-config-date-1.5.15-1.noarch.rpm

Done.

athlon
------

There is not an athlon-specific rpm for glibc, so the athlon case should 
proceed just like the i586 case above, except begin by switching to the 
athlon directory and running:

rpm -Fvh kernel-2.4.20-30.9.athlon.rpm

Note that I have not tried this.  I have an athlon-based system, but it 
runs Debian unstable! {8->

Regards,
CDRigby


_______________________________________________
Original home page of the RULE project: www.rule-project.org
Original Rule Development Site http://savannah.gnu.org/projects/rule/
Original RULE mailing list: Rule-list at nongnu.org, hosted at http://mail.nongnu.org/mailman/listinfo/rule-list